Steel push bar with a latch housing, hinge plate, screws, screwdriver and tape measure on a worn bench beside an open box. — Elizabeth Gardens

High security · Elizabeth Gardens

High Security Locks

Open 24/7

You have lost count of how many people have had a key to your house over the years: cleaners, a contractor, a former partner, the previous owner's family. The lock still works, but you no longer know who else it works for.

Request a visit

In plain words

Upgrading to high security rarely means new doors or a big disruption. Many high security cylinders retrofit into the existing deadbolt or lever, so the door preparation stays as it is and only the cylinder and keys change. A heavier deadbolt uses the same bore as the old one in most cases. The strike and hinge screws are swapped for long ones that bite into the framing. The visible difference afterwards is small; the practical difference is that the door resists the tools and tricks that defeat ordinary hardware, and that nobody can copy your key without you knowing.

Sound familiar?Elizabeth Gardens

The call: You jiggle the key a little and the old deadbolt opens even when the cut does not look quite right. If your worn key can do that, you wonder what a stranger with the right tools could do.

NextHow the visit goes

High Security Locks · Elizabeth Gardens

How the visit goes

Metal key-cutting machine with a key clamped in its vise, a clear guard over the cutter and a black handle. — Elizabeth Gardens

Scene 1
The fit of new hardware to old doors
Older houses in this region have doors that predate modern hardware: narrower stiles, a mortise pocket already cut, a thick slab door or a steel-clad door with a specific backset. The locksmith measures the bore, backset, door thickness and edge preparation so the chosen deadbolt or cylinder fits without hacking at the door. Where a mortise lock is present, a high-security mortise cylinder often replaces the old one directly. Where a knob lock is the only lock, the assessment includes where a new deadbolt bore would sit and whether the frame can take a proper strike.
Scene 2
Retiring the old keys and closing gaps
Part of the visit is making the old keys meaningless. Once the new cylinders are in, every previous key is tried to confirm it no longer operates anything, and any remaining door on the old keyway is either upgraded or at least rekeyed so an unknown copy has nowhere to go. The locksmith also closes small gaps found during the assessment: replacing hinge screws with long ones, adjusting a closer, adding a cylinder guard, or moving a thumb-turn away from glass. The door leaves the visit as one coherent assembly rather than one strong part among weak ones.
Scene 3
Fewer keys, clearer purpose
Many customers finish the visit carrying fewer keys than they started with. Exterior doors keyed alike mean one key for the house; a small master system means a manager carries one key for the whole premises. Each key has a known job. The locksmith explains which key opens which door and leaves that in writing, so the tenth person to ask does not get a shrug. Should you add a door later, a gate, a garage entry or a new office, it can join the same system so you keep the single-key convenience without opening a fresh keyway.

In the van

Reinforced strike plate
Three-inch strike and hinge screws
Code key cutting machine
Commercial mortise lock body
Key control authorisation card

What shapes the quoteElizabeth Gardens Locksmith Pros

Documentation and registration: Setting up the key register, recording signatories and providing a written schedule of cylinders and keys is real work on a business system and is listed rather than hidden.
Exit devices and closers on the same door: Where a commercial door carries a push bar or closer, the new lock must work with them, and adjusting or replacing that hardware is part of the same visit.
Number of keys cut: Every key is cut from code on a machine that handles side bitting or angled cuts, so the count of keys you want at handover is a real line rather than a rounding error.

FeesSame any hour

Have it ready

Before you call · 0 / 3

For a business, who should be allowed to authorise new keys?
Is there a window or sidelight within reach of the lock?
Would you like all doors on one key, or different keys for different areas?

(289) 816-2265

Straight answers

What proof do I need to show before locks are changed?

The locksmith confirms that the person ordering the work is entitled to change the locks: the owner, a tenant with the landlord's agreement, or a property or facilities manager for a business. Photo identification and something linking you to the address usually settle it, and for a company a letter or a call to the named contact does the same. It protects you as much as anyone, since the same check stops someone else from changing your locks.

Do high security locks need special maintenance?

Only light care. Use the dry lubricant the locksmith recommends once or twice a year, never oil, which gathers grit around the finger pins and sidebar. Keep the keyway free of debris and insert the key fully before turning. In winter, warm a resisting key in your hand or use a de-icer rather than forcing it. Check hinge and strike screws each season so the door stays aligned. Treated this way the cylinder lasts for decades.

Are high security locks only for businesses?

Not at all. Homes are the most common place they are fitted, especially after a move, a break-in nearby, or the realisation that too many keys have been handed out over the years. A graded deadbolt with a patented cylinder and a reinforced strike is a modest, quiet upgrade for a front or side door. Businesses tend to go further, with laboratory-rated cylinders, heavy lock bodies and a documented key system across many doors.